Hardware engineering company

Hardware engineering, from circuit board to working machine.

Bentra Engineering designs and builds embedded systems, electronics, mechatronic machines and robots, and the software and machine learning that make them smarter. One team, one accountable partner.

Close view of a circuit board beside a robot arm on an engineering workbench

Product engineering

Six disciplines, one engineering team

We are a hardware-first engineering company. The software we write is the kind that runs on and around machines, built by the same team as the hardware.

Embedded systems

Microcontroller boards and the firmware that runs on them, for devices that have to work reliably in the field.

  • Firmware for microcontrollers
  • Sensor and actuator integration
  • Wired and wireless connectivity
  • Low-power operation

Electronics and electrical engineering

Circuit and board design, power and control systems, taken from schematic to a tested, working unit.

  • Schematic and PCB design
  • Power supply and battery systems
  • Control panels and wiring
  • Prototype assembly and testing

Mechatronics

Mechanics, electronics and control designed together, so the moving parts and the logic that drives them fit from the start.

  • Mechanical design and CAD
  • Motor and motion control
  • Sensing and feedback loops
  • System integration and testing

AI and robotics

Robots and automated machines that sense, decide and act, taking over repetitive or hazardous work.

  • Robot design and control
  • Computer vision and perception
  • Navigation and motion planning
  • Automation of manual tasks

Machine learning

Models that give hardware judgement, running on the device or beside it.

  • Data collection from sensors
  • Model training and evaluation
  • On-device inference
  • Fault and anomaly detection

IoT and systems software

Software written for hardware: from the code inside a chip to the programs on an industrial computer, and the links that let devices talk to each other.

  • Firmware and device drivers
  • Embedded Linux and single-board computers
  • IoT connectivity and device data
  • Tools that control and monitor machines

Energy and power

Reliable power, measured and accounted for

For facilities where power is both a cost and a risk, we design and install the supply and provide the monitoring that shows how it is being used.

Solar and energy storage

Solar PV and battery systems delivered end to end, sized to the load they have to carry.

  • Site survey and load assessment
  • System design and sizing
  • Supply, installation and commissioning
  • Scheduled maintenance

Power distribution and control

Systems that deliver power safely from the source to every load.

  • Main and sub-distribution boards
  • Automatic changeover and transfer systems
  • Protection and earthing
  • Testing and commissioning

Low-voltage switchgear and software

Switchgear assemblies and the software that supervises them.

  • Switchboards and motor control centres
  • Control and automation panels
  • Remote monitoring and control software
  • Maintenance scheduling and fault alerts

Instruments and metering

Measurement you can bill from, audit against and act on.

  • Energy meters and sub-metering
  • Consumption and load monitoring
  • Sensors and process instruments
  • Reports for energy audits and cost allocation
  • Keep power available where it matters
  • Reduce energy spend with measured data
  • Plan maintenance before equipment fails

Industrial systems

Machines designed and fabricated to order

When a standard machine does not fit the job, we design and build one that does, and fit the drives and controls that run it.

Electrical machines and control

Motors, generators and the controls that run them.

  • Motor starters and variable speed drives
  • Generator control panels
  • Machine automation and control
  • Installation and commissioning

Custom machines and fabrication

Purpose-built machines and systems, designed and fabricated to your specification.

  • Design and engineering drawings
  • Fabrication and assembly
  • Motor, drive and control integration
  • Testing before delivery

Why Bentra

One team, from schematic to working machine

Hardware projects tend to go wrong at the joins: between the board and the enclosure, the firmware and the network, the prototype and the production unit. We keep those joins inside one team.

  • No hand-offs between vendors

    Electronics, mechanics, firmware and software are designed together, so problems surface on our bench and not at your launch.

  • Something working early

    You see a prototype before any large commitment, and decide the next step with evidence in your hands.

  • One accountable partner

    A fixed point of contact from the first conversation to support after launch.

How we work

From first conversation to handover

  1. Understand

    We start with your need, your site or specification, and your budget, and tell you plainly if we are not the right fit.

  2. Design

    Drawings, schematics, calculations and a plan, reviewed with you before anything is built or installed.

  3. Build

    We prototype, fabricate or install, and show you working progress early.

  4. Test and commission

    We test against the conditions the system will meet in service, and fix what fails.

  5. Hand over and support

    Documentation at handover. We stay on for maintenance, fixes and the next phase.

Start a project

Tell us what you're building

Send a few lines about your project and what you need from it. The first conversation is free.

Email us

or write to info@bentraengineering.com

Helpful to include

  • What the product or machine should do
  • Where you are today: an idea, a prototype or an existing product
  • Your timeline